Mazda Mazda6 Recalls: Every NHTSA Recall by Model Year

Component: Fuel system

Mazda6 model years: 2018 · about 121,038 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2018 Mazda3, Mazda6, 2019 CX-3, 2018-2019 MX-5, CX-5, CX-9, and 2019-2020 Mazda2 vehicles. The impeller inside the low-pressure fuel pump may crack and deform, potentially causing the fuel pump to fail.

The risk: Fuel pump failure may cause an engine stall, increasing the risk of a crash.

The fix: Dealers will replace the fuel pumps, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 5321K.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2009–2012 · about 69,879 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2003–2008 · about 47,006 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2004-2005 MPV, 2004 RX-8, and 2006-2007 Mazdaspeed6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 2618F. Note: This recall supersedes recalls 13V130, 14V362, 14V773 and 15V869.

Component: Powertrain / transmission (automatic transmission, control module (tcm/pcm/tecm))

Mazda6 model years: 2018–2019 · about 262,220 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2018-2019 CX-5, Mazda6, and 2019 Mazda3 vehicles. A software error in the powertrain control module (PCM) may cause the engine to stall.

The risk: An unexpected stall increases the risk of a crash.

The fix: Mazda will notify owners, and dealers will reprogram the PCM software, free of charge. The recall began August 20, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 3719F.

Component: Structure

Mazda6 model years: 2011–2013 · about 51,118 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.

The risk: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2010–2013 · about 155,436 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

Component: Structure

Mazda6 model years: 2009–2010 · about 50,176 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.

The risk: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2003–2008 · about 308,591 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2006-2007 Mazdaspeed6 and 2004 MPV vehicles nationwide. Mazda is also recalling 2005-2006 MPV vehicles in Alabama, Arizona, Arkansas, California, Delaware, the District of Columbia, Florida, Georgia, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands. On July 9, 2019 this recall was expanded to include certain 2004-2011 RX-8 vehicles that were previously recalled under 16V-354 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began July 6, 2018. Mailing to the affected RX-8 owners began July 6, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 2618F. Note: With the addition of the RX-8 vehicles, this recall fully supersedes recall 16V354.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2009–2010, 2013 · about 70,227 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.

Component: Air bags (sensor, occupant classification)

Mazda6 model years: 2016 · about 51,943 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2016 Mazda6 vehicles. Debris from the welding process during manufacturing of the front passenger seat frame may damage the occupant classification system (OCS) wiring.

The risk: If the wiring becomes damaged, there may be a loss of power steering assist and the deactivation of the passenger air bag, increasing the risk of a crash and the risk of injury in the event of a crash.

The fix: Mazda will notify owners, and dealers will attach a protective pad on the seat frame. If the OCS harness is damaged, insulating tape will be applied to the harness. These repairs will be performed free of charge. The recall began October 26, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1517H.

Component: Air bags (frontal, driver side, inflator module)

Mazda6 model years: 2003–2008 · about 308,992 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain model year 2003-2008 Mazda6, 2004-2008 RX-8, and 2006-2007 Mazdaspeed6 vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion and other factors, including manufacturing variability that, over time, could cause the inflator to rupture.

The risk: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the driver's frontal air bag inflator with an alternate inflator, free of charge. The recall began on September 12, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1417G. Note: This recall supersedes recall 15V-382.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2009, 2012 · about 79,402 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain 2012 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Mazda is recalling certain 2009 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Mazda is recalling certain 2007-2008 CX-7 and CX-9 sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

The risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger side air bag inflator with an alternate inflator, free of charge. The recall began October 4, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 17V-012.

Component: Air bags (frontal, passenger side, inflator module)

Mazda6 model years: 2009–2011 · about 205,377 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

The risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

The fix: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.

Component: Parking brake

Mazda6 model years: 2014–2015 · about 227,814 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda6 and 2014-2016 Mazda3 vehicles. Water could possibly enter the brake caliper causing the parking brake actuator shaft to corrode and possibly bind.

The risk: If the parking brake actuator shaft binds, the parking brake may not engage or disengage fully. If the parking brake does not engage properly, the vehicle may move unexpectedly if it is parked on a slope, increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will check the parking brake actuator shafts, replacing any that are corroded, free of charge. Remedy parts are currently unavailable. Interim notices informing owners of the safety risk were mailed August 24, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1217F.

Component: Exterior lighting (turn signal)

Mazda6 model years: 2017 · about 180 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain model year 2017 Mazda6 vehicles manufactured August 12, 2016, to September 28, 2016 and equipped with optional accessory fog lights. Due to an incorrect combination switch being installed, the turn signals may not automatically cancel by the rotation of the steering wheel. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

The risk: A vehicle continuously driven with the turn signal flashing may result in confusion to other drivers, increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will replace the combination switch, free of charge. The recall began December 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0316J.

Component: Air bags (frontal, sensor/control module-inactive)

Mazda6 model years: 2009–2010 · about 41,918 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.

The risk: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

The fix: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.

Component: Tires (pressure monitoring and regulating systems)

Mazda6 model years: 2014–2015 · about 99,711 vehicles in the whole campaign

The problem: Mazda North American Operations (Mazda) is recalling certain model year 2014-2015 Mazda6 vehicles manufactured October 25, 2012, to October 10, 2014. If the pressures of four of the tires on an affected vehicle gradually drop at the same time, the tire pressure monitoring system (TPMS) may not warn the driver of the drop in pressure. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard (FMVSS) No. 138, "Tire Pressure Monitoring System."

The risk: A vehicle that is driven with under inflated tires may experience a sudden tire failure, increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will update the TPMS software, free of charge. The recall began on December 10, 2014. Owners may contact Mazda customer service at 1-800-222-5500.

Component: Electrical system (alternator/generator/regulator)

Mazda6 model years: 2014–2015 · about 5,700 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain model year 2014 Mazda3 vehicles manufactured June 12, 2013, through December 18, 2013, and model year 2014-2015 Mazda6 vehicles manufactured May 20, 2013, through December 4, 2013, and both equipped with a 2.5L engine and a regenerative engine braking system. When driving the affected vehicles in heavy rain or in deep puddles, the alternator belt may slip causing the Power Control module (PCM) to incorrectly assume failure of the charging system.

The risk: Once the PCM assumes that the charging system has failed, the vehicle will stop charging and could result in poor acceleration, loss of steering assist and windshield wiper operation, and a possible engine stall, increasing the risk of a crash.

The fix: Mazda will notify owners, and dealers will reprogram the PCM with updated software, free of charge. The recall began on May 19, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's number for this recall is 7314D.

Component: Fuel system

Mazda6 model years: 2014 · about 19,000 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain model year 2014 Mazda6 vehicles manufactured October 25, 2012, through May 9, 2013. In the affected vehicles, it is possible to fill the fuel tank beyond its rated capacity.

The risk: If the tank is overfilled, gas may flow into the charcoal canister (an evaporative emissions component) and possibly leak from the canister's external vent, increasing the risk of a fire.

The fix: Mazda will notify owners and dealers will inspect and add an adapter to the shut off valve in the fuel tank and also inspect the charcoal canister for the presence of gasoline, replacing it as necessary, free of charge. The recall began on May 19, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's number for this recall is 7414D.

Component: Fuel system

Mazda6 model years: 2010–2012 · about 42,000 vehicles in the whole campaign

The problem: Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.

The risk: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.

The fix: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

Component: Latches, locks & linkages (doors, latch)

Mazda6 model years: 2009–2013 · about 161,400 vehicles in the whole campaign

The problem: Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.

The risk: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.

The fix: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

Component: Fuel system

Mazda6 model years: 2009–2010 · about 52,000 vehicles in the whole campaign

The problem: MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.

The risk: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.

The fix: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.

Component: Exterior lighting (headlights)

Mazda6 model years: 2003–2006 · about 42,540 vehicles in the whole campaign

The problem: DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

The risk: DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

The fix: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

Component: Exterior lighting

Mazda6 model years: 2003–2007 · about 16,270 vehicles in the whole campaign

The problem: SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

The risk: DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

The fix: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

Component: Equipment

Mazda6 model years: 2003–2009 · about 2,323 vehicles in the whole campaign

The problem: THULE, INC. IS RECALLING 2,323 OWNER-INSTALLED ROOF-MOUNTED FIT KITS, MODELS 3068 AND 3069, MANUFACTURED BETWEEN JANUARY 1, 2008 AND FEBRUARY 28, 2009 THAT ARE USED WITH THULE PODIUM FOOT PACKS, MODELS 460 AND 460R. THESE FIT KITS WERE SOLD AS AFTERMARKET EQUIPMENT FOR USE ON THE VEHICLES LISTED ABOVE. THE BOLT(S) USED TO SECURE THE FOOT TO THE VEHICLE WAS MANUFACTURED TO A HARDNESS THAT MAY CAUSE THE BOLT(S) TO BE BRITTLE AND POTENTIALLY BREAK UNDER STRESS.

The risk: THIS MAY RESULT IN THE BOLT(S) SNAPPING OFF DURING USE OR WITHOUT A LOAD. THE UNSECURED RACK AND LOAD CAN THEN COME LOOSE WHILE DRIVING CREATING A POTENTIAL ROAD HAZARD, POSSIBLY RESULTING IN A VEHICLE CRASH.

The fix: THULE WILL MAIL A RETRO FIT KIT ALONG WITH REPAIR INSTRUCTIONS TO OWNERS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 13, 2009. OWNERS MAY CONTACT THULE TOLL-FREE AT 1-800-238-2388.

Component: Structure (body, door, hinge and attachments)

Mazda6 model years: 2009 · about 29,000 vehicles in the whole campaign

The problem: MAZDA IS RECALLING 29,000 MY 2009 MAZDA6. THE OUTER DOOR HANDLES MAY STICK WHICH MAY PREVENT THE DOOR FROM LATCHING. THIS SITUATION MAY ALLOW THE DOOR TO OPEN WHILE THE VEHICLE IS IN MOTION.

The risk: DRIVING THE VEHICLE WITH THE DOOR UNLATCHED COULD LEAD TO AN UNBELTED OCCUPANT BEING EJECTED AND COULD RESULT IN DEATH OR INJURY.

The fix: DEALERS WILL INSPECT THE DOOR HANDLES AND IF NECESSARY REPAIR OR REPLACE THE HANDLES FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 13, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.

Component: Fuel system

Mazda6 model years: 2007–2008 · about 7,200 vehicles in the whole campaign

The problem: MAZDA IS RECALLING 7,200 MY 2007-2008 MAZDA6 VEHICLES WITH CALIFORNIA EMISSION SPECIFICATIONS. THE METAL FUEL TANKS ON THE AFFECTED VEHICLES MAY HAVE HAD THE PVC PROTECTIVE COATING ON THE OUTSIDE OF THE FUEL TANK DAMAGED DURING THE ASSEMBLY PROCESS WHICH MAY RESULT IN REDUCED CORROSION RESISTANCE.

The risk: THIS COULD LEAD TO PERFORATION OF THE FUEL TANK, CAUSING FUEL LEAKAGE. FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE.

The fix: DEALERS WILL INSPECT THE BOTTOM SURFACE OF THE FUEL TANK FOR DAMAGE TO THE PROTECTIVE COATING AND, IF NECESSARY, REPAIR THE COATING OR REPLACE THE FUEL TANK. THE RECALL BEGAN ON AUGUST 28, 2008. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500, OPTION 2.

Component: Seat belts (rear/other)

Mazda6 model years: 2004 · about 190 vehicles in the whole campaign

The problem: ON CERTAIN PASSENGER VEHICLES, THE RIGHT AND/OR LEFT REAR SEAT BELTS MAY NOT LOCK PROPERLY DUE TO MISSING RETAINING PINS ON THE HOUSING.

The risk: THE LOCKING MECHANISM OF THE SEAT BELT RETRACTOR MAY MALFUNCTION, INCREASING THE RISK OF DEATH OR SERIOUS INJURY TO THE REAR SEAT PASSENGERS IN THE EVENT OF A CRASH. PASSENGERS SHOULD NOT SIT AND CHILD SEATS SHOULD NOT BE USED IN THE RIGHT OR LEFT REAR SEATS UNTIL THIS DEFECT HAS BEEN CORRECTED.

The fix: DEALERS WILL INSPECT THE REAR SEAT BELTS AND REPLACE DEFECTIVE SEAT BELT RETRACTORS. THE RECALL BEGAN ON DECEMBER 27, 2004. OWNERS SHOULD CONTACT MAZDA AT 1-800-222-5500, OPTION #4.

Component: Fuel system

Mazda6 model years: 2003 · about 56,700 vehicles in the whole campaign

The problem: ON CERTAIN PASSENGER VEHICLES, THE FUEL SENDER UNIT (FSU) MAY HAVE BEEN IMPROPERLY INSTALLED IN THE FUEL TANK, PRODUCING AN INADEQUATE SEAL, AND FUEL MAY LEAK.

The risk: A FIRE COULD OCCUR IN THE PRESENCE OF AN IGNITION SOURCE.

The fix: DEALERS WILL INSPECT THE TOP OF THE FUEL TANK, AND IF NECESSARY, REPAIR OR REPLACE IT. OWNER NOTIFICATION BEGAN FEBRUARY 9, 2004. OWNERS SHOULD CONTACT MAZDA AT 1-800-222-5500.

Component: Parking brake (indicator light)

Mazda6 model years: 2002–2003 · about 45,600 vehicles in the whole campaign

The problem: CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, "PASSENGER CAR BRAKE SYSTEMS." DURING PRODUCTION, THE FLOAT IN THE FLUID LEVEL SENSOR IN THE BRAKE RESERVOIR CAN BE FORCED OFF OF THE GUIDE RAIL DURING THE FILLING OF THE MASTER CYLINDER.

The risk: SHOULD THIS OCCUR, IT IS POSSIBLE THAT THE FLOAT WILL NOT RETURN TO THE GUIDE RAIL AND THE BRAKE FLUID LEVEL WARNING INDICATOR MAY NOT FUNCTION.

The fix: MAZDA HAS NOT YET PROVIDED A REMEDY FOR THIS CAMPAIGN. OWNER NOTIFICATION BEGAN JULY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MAZDA AT 1-800-222-5500.

Component: Exterior lighting (fog lights)

Mazda6 model years: 2003 · about 64,000 vehicles in the whole campaign

The problem: ON CERTAIN MINI VANS AND PASSENGER VEHICLES, THE SOCKET HOLDER IN THE FOG LIGHTS IS INSTALLED IN THE LAMP CASING USING PRESSURE. DURING OPERATION OF THE FOG LIGHT, THE HEAT FROM THE BULB CAN EXPAND THE SOCKET HOLDER. THE EXPANSION CAN FORCE THE SOCKET HOLDER REARWARD. AFTER REPEATEDLY BEING SUBJECT TO THIS EXPANSION, IF THE FOG LIGHT IS ALSO SUBJECTED TO VIBRATION DURING VEHICLE OPERATION, THE SOCKET HOLDER WITH THE BULB HOLDER AND THE WIRING HARNESS MAY SEPARATE FROM THE FOG LIGHT CASING.

The risk: SHOULD THIS OCCUR, THE BULB SOCKET AND THE HARNESS CAN DROP INSIDE THE BUMPER AND POSSIBLY BUT RARELY, THE HEAT GENERATED BY THE BULB CAN CAUSE THE BUMPER TO BURN.

The fix: DEALERS WILL INSTALL A SPRING TO PREVENT THE SOCKET HOLDER FROM SEPARATING FROM THE LAMP CASE. OWNER NOTIFICATION BEGAN ON JULY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MAZDA AT 1-800-222-5500.