Computer & output circuits · Powertrain · generic (SAE-defined)
P062F: Internal Control Module EEPROM Error
P062F means a control module found a problem with its internal memory, usually because learned values or settings were not saved correctly the last time the vehicle was shut off.
Standard title per SAE J2012 / ISO 15031-6 · Updated 2026-11-11 · By CarWhere Research
How P062F sets
Control modules store learned values, adaptations and configuration data in non-volatile memory, typically writing it when the vehicle shuts down. At start-up or during operation, the module checks that this memory was written completely and reads back correctly. If a write did not finish, a checksum does not match, or the memory cannot be read, written or erased, it sets P062F. Some GM modules check whether the last shutdown write completed, while some Ford diesel modules report read, write or erase errors. Whether the warning light comes on, and after how many trips, varies by maker and module. The code can appear in the engine, transmission or other modules.
Common causes of P062F
Roughly most likely first; the actual cause depends on the vehicle and needs testing to confirm.
- Shutdown interrupted, such as the battery being disconnected too soon
- Voltage drop or weak battery while the module was saving data
- Main power relay dropping out before the module finished
- Poor ground or power supply at the module
- Software fault or incomplete programming
- Internal memory defect in the module (less common)
P062F symptoms
- Check engine or service light on (sometimes after two trips)
- Rough idle or harsh shifts until learned values are rebuilt
- Often no driveability symptoms at all
How P062F is diagnosed
- Note which module stored P062F and whether the battery was recently disconnected, jump-started or replaced
- Test the battery and charging system, and check battery terminals and grounds
- Check the module's power, ignition and ground circuits, including the main relay
- Clear the code and run several normal key-off cycles to see if it returns
- Check for module software updates and reprogram if one applies
- Replace and program the module only if the fault returns with good power and grounds
Typical fixes for P062F
- Clear the code after an interrupted shutdown and allow relearning
- Replace a weak battery or repair charging faults
- Repair poor power or ground connections, or replace a faulty main relay
- Reprogram the module with the latest software
- Replace and program the module if the memory is confirmed faulty
Replace parts only after testing confirms the cause — a code names the circuit or condition that failed a check, not necessarily the faulty part. We don’t publish per-repair prices; for what households actually spend on upkeep, see car repair costs.
Related symptoms & repair costs
Manufacturer notes
Documented in GM and Ford engine and transmission modules, including GM diesel and Saab turbo engines; warning light behavior differs between them.
Related codes & warning lights
P062F FAQ
What does code P062F mean?
P062F means a control module found a problem with its internal memory, usually because learned values or settings were not saved correctly the last time the vehicle was shut off. The standard definition is "Internal Control Module EEPROM Error."
Can I drive with a P062F code?
Usually yes. Often there are no symptoms, though idle or shifting may feel off until the module relearns its settings. Have it checked within days, especially if it keeps coming back or the vehicle does not start reliably.
Can disconnecting the battery cause P062F?
Yes. If power is cut while the module is still saving data after the key is turned off, the save may not finish and the module flags the memory on the next start. Waiting a few minutes after shutdown before disconnecting helps.
Does P062F mean I need a new computer?
Not usually. Interrupted shutdowns, weak batteries and power or ground problems are more common. A one-time code that does not return after clearing often needs no parts.
Keep researching
More computer & output circuits codes
Sources
- SAE J2012 — Diagnostic Trouble Code Definitions (standard code titles)
- ISO 15031-6 — Road vehicles: communication between vehicle and external equipment for emissions-related diagnostics, Part 6: Diagnostic trouble code definitions
- U.S. EPA — Vehicle Emissions Inspection and Maintenance (I/M) programs
- U.S. EPA, 40 CFR 86.1806-17 — Federal onboard diagnostics requirements for light-duty vehicles
- California Code of Regulations, Title 13, § 1968.2 — OBD II requirements
- General Motors — published OBD system and diagnostic documentation
- Ford — published OBD system documentation
General information written by CarWhere Research, not a diagnosis of your vehicle. Manufacturers can add their own sub-definitions and test conditions; confirm with the factory service information for your year, make and model. Before paying for a repair, check NHTSA for open recalls and your warranty booklet: federal law requires an emissions warranty on major emission-control parts such as the catalytic converter and engine computer.